Description
What is RF Lightning Surge Protector?
The RF Lightning Surge Protector N-connector male-to-female switch type coaxial airforce lightning protection (SPD, surge protector) can prevent damage caused by the antenna and the transmission and reception equipment due to feeder sensing equipment.
The RF Lightning Surge Protector is suitable for satellite wireless communication, and mobile Surge protection of coaxial airforce system signals such as base station, microwave communication, and radio-television, installed in lightning protection partition LPZ0A-1, and subsequent partitions.
This RF Lightning Surge Protector product uses a shielded housing package with a built-in high-quality high-speed overvoltage protection device, which has an efficient protection defense function on the induced lightning high-pressure pulse on the antenna feeder line.
The RF Lightning Surge Protector is supplied by C&T RF Antenns Inc, the RF components supplier, and wireless antenna manufacturer in China. contact us for more details on the RF Lightning Surge Protector such as pricing, inventory, etc.
We provide the RF antennas with other antenna radio frequencies such as 169MHz, 230MHz, 315MHz, 433MHz, 868MHz, 915MHz, Lora, VHF&UHF, NB-IoT, GSM, Wifi 2.4GHz, 5.8GHz, 2G 3G 4G LTE, GPS, 5G NR, UWB, etc.
C&T RF Antennas Inc provides the wireless antenna with many antenna types such as Dipole Antennas, Whip Antennas, Marine Antennas, Router Antennas, MIMO Antennas, PCB Antennas, FPC Antennas, Spring Antennas, etc.
RF Lightning Surge Protector Specifications
Product name switch type RF Lightning Surge Protector
Model N male to female
Interface mode N / JK
Maximum continuous working voltage (UC) 90V
Voltage Protection Level 90V (UP to) 600V
Nominal discharge current in (8 / 20μs) 10kA
Maximum discharge current IMAX (8 / 20μs) 20kA
Reaction time ta ≤ 25ns
Maximum transmission power PT 400W
Resident wave by v.s.w.r ≤1.2
Characteristic impedance 50 / 75Ω
Insert loss ≤0.2dB / 3.0GHz
Frequency range from DC-3.0GHz
Shell material brass
Shell protection rating IP65
Ground resistance Ω / line ≤4Ω / ≥ 2.5mm2
Work temperature range negative -40 ° C ~~ + 85 ° C
Air relative humidity 30% ~ 90%
Size 52 * 25 * 25 mm
Implementation standard GBIBB02.1 IEC61643-1
RF Lightning Surge Protector Features
1. The standing wave ratio is small, and the insertion loss is low (≤0.2dB);
2. High transmission rate, large frequency range;
3. When the mushing surge is invaded, there is no need to stop the electric equipment, and it does not affect the normal operation of normal equipment;
4. A variety of connections is optional.
RF Lightning Surge Protector Lightning Arrestor installation
1. In order to reliably prevent lightning attacks, you can pick a day-forward lightning protection device in the antenna output and the input end of the protected device. In the absence of less lightning, the antenna can also use only one without an amplifier.
2. Trying to weld the wire on the grounding wire on the grounding wire (the wire cross-section area is not less than 2.5 mm), and the other end is reliably connected to the lightning protection system grounded busbar, and the ground resistance is not more than 4 Ω.
3. When using the RF Lightning Surge Protector outdoors, you must pay attention to rain, do not allow rainwater to immerse the inside to cause corrosion damage.
4. This coaxial lightning surge protector product does not require special maintenance. When the system works fails, the lightning director can be removed and then checked. If the system returns to normal after the state before use, the system will be damaged, and the lightning protection coaxial lightning surge protector has been damaged and must be replaced immediately.
RF Lightning Surge Protector RF Lightning Arrestor RF Surge Arrestor installation consideration
1. This series of coaxial lightning surge protectors are not separated from the input and output, and any port can be connected to the protected device;
2. Do not reverse or receive the wrong line, remember to be charged;
3. The stripper is installed in the front of the protected device, the better the front end;
4. The coaxial lightning surge protector needs regular inspection, and the product must be replaced immediately after deterioration;
5. Grounding must be good and grounding resistance is not more than 4 ohms.
Reviews
There are no reviews yet.