4G LTE Antenna Embedded Flexible PCB Antenna

Description

What is a 4G LTE Antenna Embedded Flexible PCB Antenna?

This embedded antenna 4G LTE Antenna CTRF-ANTENNA-FPC-7027-6008-IPEX comes with the full-band frequency 4G / LTE antenna embedded antenna flex PCB antenna manufactured by C&T RF Antennas Inc for 700/800/1800/2300/2600 MHz applications.

The 4G LTE Antenna Embedded Flexible PCB Antenna has a 60x8mm flexible PCB circuit board size, 4dBi peak gain, 100mm RG 1.13 antenna extension cable, and Ipex/u.FL connector, self-adhesive sticker directly mount to the 4G terminals.

What is the QoS for LTE?

EPS system, the basic granularity of QoS control is EPS bearer (Bearer), that is, all data flows on the same bearer will receive the same QoS guarantee (such as scheduling policy, buffer queue management, link-layer configuration, etc.), different QoS guarantee requires different types of EPS bearer to provide.

In the EPS system, PDN refers to the external data networks (relative to LTE operator) such as the Internet, Enterprise Private Data Networks, etc.

The value of APN (Access Point Name) is used as an identifier for the PDN network and PDN GW is located at the boundary between EPC and PDN, EPS Bearer exists between UE and PDN GW.

Typically (GTP Based on S5/S8), the EPS Bearer can be seen as a logical circuit between the UE and the Packet Data Network Gateway (PDN-GW), (for PMIP-based S5/S8 interfaces, the EPS Bearer is generally considered to exist between the UE and the SGW). Context) in UMTS networks.

Depending on the QoS, EPS Bears can be divided into two categories: GBR (Guaranteed Bit Rate) and Non-GBR.

GBR means that the required bit rate is “permanently” allocated by the network so that the corresponding bit rate can be maintained even under network resource constraints.

The MBR (Maximum Bit Rate) parameter defines the upper limit of the rate that a GBR Bear can achieve with sufficient resources, and the value of MBR may be greater than or equal to the value of GBR.

On the contrary, Non-GBR refers to the case of network congestion, the service (or bearer) needs to withstand the reduced rate requirements because the Non-GBR bearer does not need to occupy fixed network resources, and therefore can be established for a long time. And GBR bearing is generally established only when needed.

The internal 4G LTE Antenna Embedded Flexible PCB Antenna is supplied by C&T RF Antennas Inc, the leading internal-external 4G LTE antenna manufacturer in China.

C&T RF Antennas Inc provides High-performance 4G LTE Antennas with many antenna types such as Dipole Antennas, Whip Antennas, Marine Antennas, Router Antennas, MIMO Antennas, Combo Antennas, PCB Antennas, FPC Antennas, Spring Antennas, Sector Antennas, Yagi Antennas, etc.

C&T RF Antennas Inc provides RF antennas with other antenna radio frequencies such as 169MHz, 230MHz, 315MHz, 433MHz, 868MHz, 915MHz, Lora, NFC, VHF&UHF, NB-IoT, ADS-B, GSM, Wifi 2.4GHz, 5.8GHz, 2G 3G 4G LTE, GPS, GNSS, 5G NR, UWB, etc.

Contact us for more details on the 4G LTE Antenna Embedded Flexible PCB Antenna such as 4G LTE Antenna datasheet, 4G LTE Antenna pricing, 4G LTE Antenna inventory, or other 4G LTE Antennas.

4G LTE Antenna Embedded Flexible PCB Antenna Specifications:

Internal Antenna FPC Antenna Features

RF Antennas Applications